Anthracite grey welded steel fence with arched sections and ball finials, driveway gate and letterbox in front of a yellow detached house

Welded steel.
Built for decades to come.

Every section is welded by hand, ground smooth, hot-dip galvanised and only then powder coated. This sequence is why a fence like this does not rust away from the bottom after five years.

Request a free site survey
Welded by handevery panel in our workshop
Galvanised and powder-coateddoes not flake at the bottom
Your own patternrecreated from a photo
Fixed price in writingafter the free site survey
Manufacturing

Four steps you will not see once the fence is up.

Welded, not slotted together

Every joint is welded and the seam then ground smooth. No clamps, no visible screws on the face of the fence.

Hot-dip galvanised

The finished section goes into the zinc bath in one piece. That way the protection reaches inside the tubes too, not just the outer surface.

Then powder coated

Zinc first, then colour. If steel is only painted, rust keeps working away under the paint with no sign of it from outside.

Repairable

A section hit by a car is removed, re-welded and recoated. With bonded systems, the fence would be scrap in a case like this.

Three ranges. Any pattern, made to measure.

Hardly two steel fences are alike. To help you find what suits your house, we group them into three ranges, with patterns from our own workshop. We can also recreate your own pattern from a photo of your existing fence or your neighbour's.

Vertical bars with ball or spear tops, a straight or arched top line. Suits older houses, brick and front gardens.

Steel fence with vertical bars and a sliding gate in front of a house with a red roof
Steel fence with arched panels and a gate in front of a light-coloured house
Black steel fence with spear tops and ornaments on a concrete base
Drawing of pattern Classic 01: driveway gate, pedestrian gate and fence panel in steel
Classic 01
Drawing of pattern Classic 02: driveway gate, pedestrian gate and fence panel in steel
Classic 02
Drawing of pattern Classic 03: driveway gate, pedestrian gate and fence panel in steel
Classic 03Most popular
Drawing of pattern Classic 05: driveway gate, pedestrian gate and fence panel in steel
Classic 05
Drawing of pattern Classic 06: driveway gate, pedestrian gate and fence panel in steel
Classic 06
Drawing of pattern Classic 07: driveway gate, pedestrian gate and fence panel in steel
Classic 07
Drawing of pattern Classic 08: driveway gate, pedestrian gate and fence panel in steel
Classic 08
Drawing of pattern Classic 09: driveway gate, pedestrian gate and fence panel in steel
Classic 09
Enquire without obligation

Which gate suits your driveway?

We weld the gate and pedestrian gate in the same pattern as the fence, hot-dip galvanised and powder coated.

Welded steel sliding gate with an arched top and spear tops in front of a house with a carport

Sliding gate

Double steel swing gate between light pillars in front of a town house

Swing gate

Steel pedestrian gate with ball caps on the posts beside a fence panel

Pedestrian gate

When it makes sense
When the driveway slopes down or up, or when cars park directly behind the gate.
When the driveway is level and there is no room at the side for a gate to slide.
As access for post, visitors and the bins, usually next to the main gate.
Space needed
A clear run at the side, roughly as long as the gate is wide.
A swing area on the inside, around half the gate width per leaf.
A clear opening of around 100 to 120 cm.
On a slope
First choice. Runs freely above the slope on its own ground track.
Only possible with adjustments, otherwise the leaf scrapes the ground.
Not an issue, the gate stop is adjusted to suit.
Electric motor
Sommer, radio-controlled with a remote control. Photocell safety beam as standard.
Sommer, one motor per leaf.
Electric strike lock with doorbell on request.
Enquire about a matching gate

What customers want to know first.

Why is steel more expensive than aluminium?
Because of the handwork. Welding, grinding and the extra trip through the zinc bath take time. The material itself is cheaper than aluminium; the labour is not.
Will the fence rust eventually after all?
Where deep damage goes right down to the bare metal, light surface rust can appear. But because there is zinc underneath, it does not spread any further. You can touch it up with a paint pen.
Can I mix steel and aluminium?
Yes, that is common: steel for the fence facing the street, aluminium along the sides and at the back. It still looks calm and consistent as long as the colour and height match.
Can you make wrought elements based on an old original?
If you send us a photo of your existing fence or the neighbouring property, we will recreate the pattern. For heritage-protected properties (Denkmalschutz), we agree everything with you and the authorities beforehand.
Adrian Mech

Tell us what you need, or leave your number.
We will call you back.

Adrian Mech, owner of Inoveria · reply within 24 h · free site survey

Free estimateStep 1 of 2

What are you looking for?

We will ask about the rest on the phone.